基于Ansoft 平台的五金工具充磁磁场分析

电气工程论文编号:DQ196   论文字数:22797,页数:70

目 录

摘  要 I
Abstract II
1  前 言 1
 1.1  电磁场理论的建立与发展 1
 1.2  有限元方法的发展及应用 2
 1.3  有限元方法在电磁场分析中的应用 4
 1.4  本文所需完成的工作 5
2  Ansoft Maxwell简介 6
 2.1  Ansoft Maxwell的应用背景 6
 2.2  Ansoft Maxwell的发展方向 7
 2.3  Ansoft Maxwell3D介绍 7
 2.4  Ansoft Maxwell3D简要操作流程 9
3  充磁线圈磁场有限元分析 11
 3.1  充磁线圈有限元建模 11
 3.1.1  圆柱体充磁线圈有限元建模 11
3.1.2  长方体充磁线圈有限元建模 12
3.1.3  八面体充磁线圈有限元建模 14
 3.2  设定充磁线圈求解条件 16
3.2.1  指定模型各部分的属性 16
3.2.2  指定边界条件和激励源 16
3.2.3  指定求解规范 17
3.2.4  求解条件验证 17
 3.3  后处理器分析 18
3.3.1  圆柱体充磁线圈的求解分析 18
3.3.2  长方体充磁线圈的求解分析 26
3.3.3  八面体充磁线圈的求解分析 34
 3.4  导出分析结果 42
 3.5  MATLAB辅助分析 42
3.5.1  MATLAB分析流程 42
3.5.2  MATLAB分析圆柱体充磁线圈导出结果 43
3.5.3  MATLAB分析长方体充磁线圈导出结果 50
3.5.4  MATLAB分析八面体充磁线圈导出结果 56
 3.6  分析结果总结 63
4  结论 64
致  谢 65
参考文献 66

摘  要

 为了适应不断提高的五金工具生产要求，满足当今社会的发展需要，对五金工具进行充磁磁场研究变得刻不容缓。而通过运用Ansoft Maxwell3D软件平台，针对不同形状与类型的充磁线圈结构，建立相应的数学模型，经过一系列的条件设定后，利用有限元方法进行分析研究，从而得到充磁线圈内部空间的磁场分布。并运用MATLAB软件对所得结果进行辅助分析，导出磁通密度空间分布图。对所得图表进行系统而全面的分析，最终得出结论。所获得的研究结论与实际结果基本一致。研究结果充分分析充磁线圈的磁场特性，有助于改善五金工具的生产工艺，优化五金工具的磁场特性，对提高相应产品的生产质量，提升产品的市场竞争力有积极意义，并且为进一步研究五金工具充磁磁场创造有利条件。
 
 
关键词：充磁线圈磁场分析、Maxwell3D、有限元建模、有限元分析

Abstract

For the adaption to the development of hardware technology and meet social demands, it becomes urgent to research the magnetic of charging coil for hardware. The Ansoft Maxwell3D was used to build different kinds of magnetic of charging coil mathematical models and to set a series of factors. The finite element method was used to get the inner magnetic distribution of charging coil. Then the MATLAB was used to analyze the results that came from Maxwell3D, the magnetic flux density spatial distributions diagrams were exported and they were analyzed entirety. Finally the conclusion was completed the same as the actual result. The magnetic field characteristics of magnetic of charging coil was researched fully, so it is benefit to increase the product technology and optimize magnetic characteristics, therefore, the product quality is improved and the product competitive power is advanced. What's more, a condition that research hardware magnetic field deeply is created.

 Keywords：magnetic of charging coil researching, Maxwell 3D, finite element method modeling, finite element method analysis