手持圆弧倒角机的设计

机械论文编号:JX409  包括设计图,说明书字数:8205.页数:24

 目      录
摘要－- - - - - - - - - - - - - - - - - - - - - - - - - - - - -－一2
引言－- - - - - - - - - - - - - - - - - - - - - - - - - - - -  －一3
第一章．倒角机总体设计－- - - - - - - - - - - - - - - - - - - - －一4
1 . 1 被加工零件的加工精度和加工工序－- - - - - - - - - - -  - －一4
1 . 2 确定切削用量及选择确定切削用量刀具－- - - - - - - - -  - －一4
1 . 3 倒角机方案的确定－- - - - - - - - - - - - - - - - - - -- －一6
第二章．电机的选择－- - - - - - - - - - - - - - - - - - - - - - －一7
第三章．圆锥齿轮的传动的设计－- - - - - - - - - - - - - - - - - －一8
3 . 1 选择齿轮材料及热处理方法－- - - - - - - - - - - - - - -  －一8
3 . 2 计算齿轮的许用应力－- - - - - - - - - - - - - - - - - - -－一8
3 . 3 齿轮参数设计－- - - - - - - - - - - - - - - - - - - - -  －一9
第四章．轴的设计－- - - - - - - -  - - - - - - - - - - - - - - －一12
4 . 1 ．传动装置设计－- - - - - - -  - - - - - - - - - - - - - －一13
4 . 2 选取轴的材料和热处理的方法－- - - - - - - - - -- - - -  －一14
4 . 3 轴的结构设计－- - - - -  - - - - - - - - - - - - - - -- －一14
4 . 4 轴的强度计算－- - - -  - - - - - - - - - - - - - - - -- －一14
4 . 5 选用键并校核强度－- - - - - - - - -  - - - - - - - - -- －一17
第五章．盖体的设计－- - - - - - - -  - - - - - - - - - - - - - －一18
第六章．可调夹板的设计－- - - - - - -- - - - - - - - - - - - - －一19
6 . 1 毛坯的选择－- - - - - - - - - -  - - - - - - - - - -  - －一19
6 . 2 工艺路线的拟定－- - - - - - - - - - -  - - - - - - -  - －一19
第七章．润滑系统－- - - - - - -- - - - - - - - - - - - - - - - －一21
参考文献－- - - - - - ---- - - - - - - - - - - - - - - - - -- －一22
小结－- -- - - - - - - - - - - - - - - - - - - - - - -  - - - －一23

摘要
    倒角机它用于工件的规则曲面（如外圆，内孔，腰形孔等）和不规则的内，外腔棱边的倒角，特别用于大型工件的一些曲边的倒角，一般机器无法加工，采用手提圆弧倒角机倒角即方便又快捷。
    本文是对手持圆弧倒角机的研究，主要通过对倒角机的电机的选择、齿轮各个参数的选定、传动轴材料强度的要求等几个方面的计算确定设计方案是否可行，并在确定可行性方案后把手持圆弧倒角机的结构设计的紧凑、轻巧、操作方便。
关键词:倒角机,电机,齿轮

Abstract
    chamfering machine is used to the rules of the workpiece surface (such as cylindrical, inner hole, waist-shaped hole, etc.) and irregular inside and outside the cavity of the chamfered edge, especially for large parts of the chamfered edges of some songs the general machinery can not be processed, using hand-held circular chamfering machine chamfering the convenient and fast. This is a hand-held circular chamfering machine studies, mainly through the choice of chamfering machine motor, gear selection of the parameters, shaft material strength requirements and so on several aspects of the calculations to determine the feasibility of design, and the to determine the feasibility of the program after the hand-held circular chamfering machine structural design of the compact, lightweight, easy to operate.
Key words: chamfering machines, motors, gear